2019-2020 2020-2021 2021-2022 2022-2023 2023-2024
Browse
by subject...
    Schedule
view...
 

1 - 6 of 6 results for: EE101A

CS 241: Embedded Systems Workshop (EE 285)

Project-centric building hardware and software for embedded computing systems. This year the course projects are on a large interactive light sculpture to be installed in Packard. Syllabus topics will be determined by the needs of the enrolled students and projects. Examples of topics include: interrupts and concurrent programming, mechanical control, state-based programming models, signaling and frequency response, mechanical design, power budgets, software, firmware, and PCB design. Interested students can help lead community workshops to begin building the installation. Prerequisites: one of CS107, EE101A, EE108, ME80.
Terms: Win | Units: 3 | Repeatable 3 times (up to 9 units total)
Instructors: Levis, P. (PI)

EE 101A: Circuits I

Introduction to circuit modeling and analysis. Topics include creating the models of typical components in electronic circuits and simplifying non-linear models for restricted ranges of operation (small signal model); and using network theory to solve linear and non-linear circuits under static and dynamic operations. Prerequisite: MATH 20 (or equivalent) is required, and ENGR 40M is strongly recommended.
Terms: Win, Sum | Units: 4 | UG Reqs: GER:DB-EngrAppSci, WAY-SMA

EE 101B: Circuits II

Continuation of EE101A. Introduction to circuit design for modern electronic systems. Modeling and analysis of analog gain stages, frequency response, feedback. Filtering and analog to digital conversion. Fundamentals of circuit simulation. Prerequisites: EE101A, EE102A. Recommended: MATH 53 or CME102.
Terms: Spr | Units: 4 | UG Reqs: WAY-SMA, GER:DB-EngrAppSci

EE 273: Digital Systems Engineering

Electrical issues in the design of high-performance digital systems, including signaling, timing, synchronization, noise, and power distribution. High-speed signaling methods; noise in digital systems, its effect on signaling, and methods for noise reduction; timing conventions; timing noise (skew and jitter), its effect on systems, and methods for mitigating timing noise; synchronization issues and synchronizer design; clock and power distribution problems and techniques; impact of electrical issues on system architecture and design. Prerequisites: EE101A and EE108A. Recommended: EE114/214A.
Last offered: Winter 2022

EE 285: Embedded Systems Workshop (CS 241)

Project-centric building hardware and software for embedded computing systems. This year the course projects are on a large interactive light sculpture to be installed in Packard. Syllabus topics will be determined by the needs of the enrolled students and projects. Examples of topics include: interrupts and concurrent programming, mechanical control, state-based programming models, signaling and frequency response, mechanical design, power budgets, software, firmware, and PCB design. Interested students can help lead community workshops to begin building the installation. Prerequisites: one of CS107, EE101A, EE108, ME80.
Terms: Win | Units: 3 | Repeatable 3 times (up to 9 units total)
Instructors: Levis, P. (PI)

EE 292S: Understanding the Sensors in your Smartphone

This course provides an introduction to the sensor systems found in modern-day smartphones, wearables, and hearable devices. As much as we take their functionality for granted, there is a tremendous amount of engineering needed to sense "real world" signals such as acceleration, touch, or altitude. There will be an overview on the actual circuitry and hardware used in sensor implementations, with a focus on MEMS devices (eg, accelerometer/gyro), going up through the algorithms commonly seen in sensors processing, and finally fusion of data from multiple sensors to yield final data presented to a user. The four broad areas that will be covered are: Inertial sensing/movement; Touch sensing/authentication; Health sensing (PPG, ECG, SpO2); Next-generation (force, radar/ranging, ultrasonics, and more). There is a lab/project associated with each of these areas, each project spanning roughly two weeks. The projects are designed to be more at a system level; the student will be required to ex more »
This course provides an introduction to the sensor systems found in modern-day smartphones, wearables, and hearable devices. As much as we take their functionality for granted, there is a tremendous amount of engineering needed to sense "real world" signals such as acceleration, touch, or altitude. There will be an overview on the actual circuitry and hardware used in sensor implementations, with a focus on MEMS devices (eg, accelerometer/gyro), going up through the algorithms commonly seen in sensors processing, and finally fusion of data from multiple sensors to yield final data presented to a user. The four broad areas that will be covered are: Inertial sensing/movement; Touch sensing/authentication; Health sensing (PPG, ECG, SpO2); Next-generation (force, radar/ranging, ultrasonics, and more). There is a lab/project associated with each of these areas, each project spanning roughly two weeks. The projects are designed to be more at a system level; the student will be required to explore the performance and limitations of sensing hardware, and then take that understanding to solve real-world sensor problems. All projects will be built on a Raspberry Pi with various sensor boards; students should be comfortable with wiring up a small breadboard, and coding on an RPi a high-level language such as Python or Java. Prerequisites: EE101A, EE102A, and CS106A or equivalents.
Terms: Aut | Units: 3
Filter Results:
term offered
updating results...
teaching presence
updating results...
number of units
updating results...
time offered
updating results...
days
updating results...
UG Requirements (GERs)
updating results...
component
updating results...
career
updating results...
© Stanford University | Terms of Use | Copyright Complaints